Interior protection is not armed, which allows movement within premises without causing alarm. When on, the opening of windows or doors while the system is disarmed will sound 3 beeps at the keypad s. While the system is disarmed, this indicator will go on and off as protection zones are closed and opened. If the indicator is off, the system may still be operating, but on its backup battery power. Individual keys A , B , and C key D not used.
On some keypads, these keys are not present, and the following key pairs may be available, instead, for emergency functions:. If 2 seconds elapses without a key depression, the entry is aborted and must be repeated from its beginning.
At the time of installation, your installer programmed a personal four-digit Master code, known only to you and yours. This code is used to perform most system functions, including arming and disarming of the system. As an additional safety feature, temporary user codes can be assigned see next page for use by those not having a need to know the Master code. Note that the Master code remains in effect even when other user codes are assigned.
This feature is intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the central station of your situation, if that service has been provided. Important: The Duress code is useful only when connected to a central station. If your system supports "Quick Arming", the " " key can be pressed in place of the security code when arming the system.
The security code is always required, however, when disarming the system. It is recommended that obvious codes such as 1 1 1 1 or 1 2 3 4 not be assigned. Enter single-digit user number '2', '3', '4', '5', '6' or '7' for which a code is to be assigned, changed, or deleted. I f assigning or changing a user's code, enter the desired 4-digit code for use by that user number.
The keypad will beep once. In a few moments the keypad will beep once, indicating that the existing code has been deleted. The Master code can be changed by the main user of the system. To change it, do the following:. Important: Temporary users should not be shown how to use any system function they do not need to know e.
General Information Your system has preset time delays, known as exit delay and entry delay. The system must be disarmed, however, before the entry delay period ends, or an alarm will occur. The keypad will beep slowly during the entry delay period, reminding you to disarm the system. These modes can provide greater security while you are sleeping or while you are away for extended periods of time.
The READY key can be used to display all faulted zones, making it easier for you to secure any open zone. Secure or bypass the zones displayed before arming the system. A "Ready" message will be displayed when all protection zones have been either closed or bypassed and the keypad's READY indicator light if present will be lit. This key is used when you want to arm your system with one or more zones intentionally unprotected. The system must be disarmed first. Enter zone number s for the zone s to be bypassed e.
Single digit zone numbers must be preceded by a zero e. When finished, the keypad will display a "Bypass" message along with each bypassed zone number, accompanied by a beep for each. Wait for these zones to be displayed, to confirm their bypass.
This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
Any alarm system, whether commercial or residential, is sub ject to compromise or failure to warn for a vari ety of reasons. Page Ademco Limited Warranty 24 months from the date stamp control on the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply.
Print page 1 Print document 20 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Previous Menu. Previous Page. Next Page. Page 2 Capability has been added for the control to call a pager on the secondary telephone number. This can only be used if the primary reporting format is Ademco Contact ID.
Page 3: Table Of Contents Section 6. Back Cover —3— Page 5: Section 1. General Description Section 1. Page 7: Section 2. System Installation And Wiring Section 2. Page 8: Install Remote Keypads Figure 3. While in this mode, the keypad will display the House ID transmitted by any wireless devices in the area. Page Install Wireless Transmitters Page Section 3. Programming The System Section 3.
0コメント